CM-N3-ACC
CM-N3-ACC
Pre-Trigger Remote Cable
For remotely triggering Canon cameras equipped with an N3 Remote shutter release Terminal and controlling half-press function using certain PocketWizard radios.
Cable length: 3' (91.5 cm)
From 1/8" (3.5 mm) Stereo Miniphone
To Canon N3 Remote Terminal
International Catalog Number: CM-N3-ACC
US Catalog Number: 802-453
PocketWizard Compatibility:
• PlusX
• Plus III
• FlexTT5
• MultiMAX with ACC port
• Use the CM-N3-P or CM-N3 for the Plus II, older MultiMAX, or other PocketWizard radios.
Description: This is a special remote motor drive cable called a Pre-Trigger Cable. A Pre-Trigger cable controls both the half-press and full-press function of your remote camera’s shutter release. When a camera is “pre-triggered”, it is like holding your camera’s shutter release button in the half-pressed or metering/focusing position.
This –ACC cable allows a compatible PocketWizard radio to independently control both half-press and full-press functions.
A standard cable works with most PocketWizard radios but has no half-press control, and is for basic remote triggering only.
A –P cable works with most PocketWizard radios. This pre-trigger cable has a switch that allows you to toggle half-press on or off at the camera position, but not remotely.
Compatible with the following radios:
PlusX: Use this cable with the PlusX to trigger the camera.
Plus III: Use this cable with the Plus III’s exclusive 2-stage trigger to wake-up or focus your remote camera just like using the camera’s shutter release button.
FlexTT5: This cable is required for relay mode with E-TTL, or other remote triggering with the FlexTT5. Learn more here. You can use a –P cable or standard cable with a FlexTT5, but your remote camera will not be able to relay an E-TTL signal to Speedlites. The FlexTT5 does not support the 2-stage trigger function.
MultiMAX with –ACC port: Enable a remote zone with your hand-held MultiMAX, and your remote MultiMAX will wake up its remote camera with this cable. As long as the zone is turned on, the remote camera will stay awake and respond more quickly and consistently, but also consume the camera's batteries much more quickly. When the remote zone is disabled, the camera will enter its normal sleep modes. The MultiMAX does not support the 2-stage trigger function.
Please see our PocketWizard Wiki for more details.
Compatible with cameras using Canon's N3 remote terminal including:
| Canon |
Canon |
Canon |
Kodak |
| EOS | EOS-1V |
EOS 20D |
DCS 560 |
| EOS-1D Mark II | EOS-1V HS |
EOS 30D |
DCS 520 |
| EOS-1D Mark IIN | EOS-3 |
EOS 40D |
|
| EOS-1D Mark III | EOS 5D |
EOS 50D |
|
| EOS-1D Mark IV |
EOS 5D Mark II | EOS D30 | |
| EOS-1Ds | EOS 5D Mark III | EOS D60 | |
| EOS-1Ds Mark II | EOS 6D* | EOS D2000 | |
| EOS-1Ds Mark III | EOS 7D | ||
| EOS-1D X* |
Trademarks are the property of their respective owners.
CM-N3-ACC
Pre-Trigger Remote Cable
For remotely triggering Canon cameras equipped with an N3 Remote shutter release Terminal and controlling half-press function using certain PocketWizard radios.
Cable length: 3' (91.5 cm)
From 1/8" (3.5 mm) Stereo Miniphone
To Canon N3 Remote Terminal
International Catalog Number: CM-N3-ACC
US Catalog Number: 802-453
PocketWizard Compatibility:
• PlusX
• Plus III
• FlexTT5
• MultiMAX with ACC port
• Use the CM-N3-P or CM-N3 for the Plus II, older MultiMAX, or other PocketWizard radios.
Description: This is a special remote motor drive cable called a Pre-Trigger Cable. A Pre-Trigger cable controls both the half-press and full-press function of your remote camera’s shutter release. When a camera is “pre-triggered”, it is like holding your camera’s shutter release button in the half-pressed or metering/focusing position.
This –ACC cable allows a compatible PocketWizard radio to independently control both half-press and full-press functions.
A standard cable works with most PocketWizard radios but has no half-press control, and is for basic remote triggering only.
A –P cable works with most PocketWizard radios. This pre-trigger cable has a switch that allows you to toggle half-press on or off at the camera position, but not remotely.
Compatible with the following radios:
PlusX: Use this cable with the PlusX to trigger the camera.
Plus III: Use this cable with the Plus III’s exclusive 2-stage trigger to wake-up or focus your remote camera just like using the camera’s shutter release button.
FlexTT5: This cable is required for relay mode with E-TTL, or other remote triggering with the FlexTT5. Learn more here. You can use a –P cable or standard cable with a FlexTT5, but your remote camera will not be able to relay an E-TTL signal to Speedlites. The FlexTT5 does not support the 2-stage trigger function.
MultiMAX with –ACC port: Enable a remote zone with your hand-held MultiMAX, and your remote MultiMAX will wake up its remote camera with this cable. As long as the zone is turned on, the remote camera will stay awake and respond more quickly and consistently, but also consume the camera's batteries much more quickly. When the remote zone is disabled, the camera will enter its normal sleep modes. The MultiMAX does not support the 2-stage trigger function.
Please see our PocketWizard Wiki for more details.
Compatible with cameras using Canon's N3 remote terminal including:
| Canon |
Canon |
Canon |
Kodak |
| EOS | EOS-1V |
EOS 20D |
DCS 560 |
| EOS-1D Mark II | EOS-1V HS |
EOS 30D |
DCS 520 |
| EOS-1D Mark IIN | EOS-3 |
EOS 40D |
|
| EOS-1D Mark III | EOS 5D |
EOS 50D |
|
| EOS-1D Mark IV |
EOS 5D Mark II | EOS D30 | |
| EOS-1Ds | EOS 5D Mark III | EOS D60 | |
| EOS-1Ds Mark II | EOS 6D* | EOS D2000 | |
| EOS-1Ds Mark III | EOS 7D | ||
| EOS-1D X* |
Trademarks are the property of their respective owners.